MPRLS0025PA00001A is a Honeywell pressure sensor built for compact, battery-powered designs. The built-in ASIC chip completes full factory calibration — zero drift, sensitivity, nonlinearity and thermal drift are all compensated — so error stays controlled across 0–50°C and the sensor is ready to use out of the box, eliminating external tuning cost and shortening time-to-market. Operating current is only 1.7 mA with nanoamp-level sleep mode and typical power below 10 mW — ideal for lithium-battery, wearable and handheld devices with extended runtime. The 5×5 mm SMD package with a stainless steel barbless pressure port solders directly to the PCB, with no external sensing module required. Available through YQM ELECTRONICS (YQM). Browse all Honeywell Products or the Pressure Sensors category.

Core Advantages

Factory ASIC Calibration & Full Compensation: Zero drift, sensitivity, nonlinearity and thermal drift are all calibrated at the factory by the built-in ASIC — no external tuning cost, ready to use out of the box, shortened time-to-market.
Ultra-Low Power for Battery Devices: 1.7 mA typical operating current, nanoamp-level sleep mode, typical power below 10 mW — ideal for lithium-battery, wearable and handheld designs with extended runtime.
Ultra-Compact 5×5 mm SMD Package: 5×5 mm surface-mount cube with a stainless steel barbless pressure port — direct PCB soldering, no external sensing module, maximum enclosure space savings.

Key Features

Factory CalibrationASIC full compensation — zero drift, sensitivity, nonlinearity, thermal drift

Operating Current1.7 mA typical

Sleep Modenanoamp-level power

Typical Power<10 mW

Package5×5 mm SMD

Pressure Portstainless steel, barbless

Compensated Range0–50°C controlled error

MountingPCB soldering, no external sensing module

Power Supply Fitlithium-battery devices

Use Caseswearables, handheld devices

Traditional Analog Sensors vs. MPRLS0025PA00001A

Design Challenge	Traditional Analog Sensor	MPRLS0025PA00001A
Thermal drift & calibration	Large drift over temperature, requires per-unit manual calibration	Factory ASIC full compensation — zero, sensitivity, nonlinearity, thermal drift; controlled error over 0–50°C, ready to use out of the box
Enclosure space	Bulky pressure modules are hard to fit in compact structures	5×5 mm SMD solders directly to the PCB, structural design pressure greatly reduced
Battery life	High current drain shortens runtime in battery-powered devices	Ultra-low operating current + nanoamp-level sleep, supports timed wake-up sampling for maximum power saving

Applications

⌚

Wearable Devices

Battery-powered, extended runtime

📱

Handheld Devices

Compact structure, PCB soldering

🔋

Battery-Powered Portables

<10 mW power, nanoamp sleep

🔬

Compact Equipment

5×5 mm SMD, saves internal space

FAQ

Q: Does MPRLS0025PA00001A need manual calibration?

A: No. The built-in ASIC completes full factory calibration and compensation of zero drift, sensitivity, nonlinearity and thermal drift, with controlled error over the 0–50°C range — ready to use out of the box, no calibration step required.

Q: Is it suitable for battery-powered devices?

A: Yes. Operating current is only 1.7 mA with nanoamp-level sleep mode and typical power below 10 mW, and timed wake-up sampling maximizes power saving and extends runtime.

Q: Will it fit a compact enclosure?

A: Yes. The 5×5 mm SMD package with a stainless steel barbless pressure port solders directly to the PCB, with no external sensing module required — internal structure space is saved.

Q: Where can I buy MPRLS0025PA00001A?

A: YQM ELECTRONICS supplies Honeywell products — contact us for samples and technical support.